Lab Coater Suppliers,lab Coater Manufacturers

Lab Touch Screen Digital viscometer

The display parameters are more intuitive, easy to use and operate, and the appearance is beautiful and elegant.

Tags :

NMC622 Single Side Coated Aluminum Foil for Battery Cathode Electrode Sheet

Reference for the use of Electrode Sheet: ①Electrode sheet cutting: AOT-DC-80 Cutting machine Recommended size of button electrode sheet: 12mm/14mm diameter. ②Pole piece weighing: AOT series balance active substance formula: active substance mass = (pole piece mass (mg) - disc area (cm2) * collector surface density (mg/cm2) * active substance propo1

Tags :

Lithium Battery Material LiBOB Poweder For Lab Research

In lithium-ion batteries, the main role of LiBOB is to transport particles and conduct current. To perform these tasks effectively, it requires high solubility and conductivity, good chemical stability, and a wide electrochemical window. The anionic structure of LiBOB molecule has delocalization, which makes it exhibit excellent performance in the 1

Tags :

Lithium Battery Cathode Material lithium difluorophosphate Poweder For Lab Research

Lithium difluorophosphate is an inorganic compound with the chemical formula LiPO₂F₂. This substance mainly appears as a white powdery solid, with a melting point higher than 300°C, a density of 1.979g/cm³, and a solubility of 40324mg/L at 20°C. Its vapour pressure is 0.000000145Pa at 25°C and 298K. Lithium difluorophosphate has a wide range of app1

Tags :

High pure Battery Material LiTFSI Poweder For Lab Research

Lithium bistrifluoromethylsulfonimide is a white crystal or powder that has good thermal stability and begins to decompose when heated to 360 ° C. It has high electrochemical stability and conductivity, and has corrosion effect on aluminum collector at high voltage (above 4.2V). Therefore, it is often used as a lithium ion battery, organic electrol1

Tags :

Heat Roller Press Machine For Battery Electrode Sheet Calendering With Winding System

1.This Roll Press Machine is a continuous roll to roll heat calendering machine . It has dual rollers of 150mm dia. x 300mm width and dual micrometer. The roll press machine is an ideal hot rolling press for adjusting thickness and increasing active material density of the electrode in Li-Ion batteries research after coating and drying. 21

Tags :

Battery Material high purity Potassium Metal Chips

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Lab Battery Slurry Vacuum Film Coating Machine with Dryer

Vacuum film coating machine is widely used in various high temperature coating process, such as ceramic film, crystal film, battery electrode, special nano film

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Double Dispersed Axis Vacuum Planetary Mixer For Lithium Battery

MSK-SFM-9-5L dual dispersing shaft vacuum planetary mixer is an efficient mixing device that integrates low-speed mixing and high-speed dispersion. It combines orbital and rotational motion to achieve thorough mixing of materials.

Tags :

Lab Flatbed Coating Machine

MSK-AFA-PD200 flatbed coating machine, equipped with extrusion coating mold, linear plunger feeding, minimum material loss of about 18ml, maximum coating size of 200x300mm, can be used in a glove box, suitable for low viscosity less than 1000mPa. s, coating thickness accuracy of ± 1 μ m, can be optionally coated with scraper, wire rod, and four sid1

Tags :

AOT-AFA-EI300 Scraper Three Roll Transfer Battery Coating Machine

AOT-AFA-EI300 scraper three roll transfer coating machine, roll to roll method, continuous and intermittent coating, width 300mm, coating width 50-260mm, coating surface density accuracy ± 1.5%, 150 ℃ hot air oven, suitable for 8-30 μ m thick metal substrates, including slurry stirring, winding correction function, optional NMP treatment and plasma1

Tags :