Al Foil For Lab Research Suppliers,al Foil For Lab Research Manufacturers

LiCl Anhydrous Lithium Chloride Powder for Solid State Electrolyte

Lithium Chloride (LiCl) Powder is a kind of battery-grade precursor to systhesize Li-based solid-state electrolyte. It has advantages such as high specific capacity and high voltage difference, which effectively enhance the power performance of the battery.

Tags :

Lithium battery coaxial double cylinder structure SSR viscometer (special for small samples) is suitable for 7ml-13ml

A new LV-SSR Brinell rotary viscometer adopts high performance stepping motor and driver, which runs accurately and smoothly according to the program setting, and the motor runs through the torque sensor to drive the rotor to rotate at constant speed. When the rotor is subjected to viscous resistance in the measured liquid, the force is fed back to1

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Al-Clad CR2032 Coin Cell Case (20d x 3.2mm) for Li-ion Battery

This is a special CR2032 coin cell case with Aluminum coated on the inside and outside of the positive can (60pcs/pack). It can tolerate polarization of higher voltages (up to 5.5V) due to the passivation of cladding by electrolyte component (especially LiPF6 based electrolyte system) to form a layer of AlF3. This AlF3 layer is 1

Tags :

Double Dispersed Axis Vacuum Planetary Mixer For Lithium Battery

MSK-SFM-9-5L dual dispersing shaft vacuum planetary mixer is an efficient mixing device that integrates low-speed mixing and high-speed dispersion. It combines orbital and rotational motion to achieve thorough mixing of materials.

Tags :

Lab Flatbed Coating Machine

MSK-AFA-PD200 flatbed coating machine, equipped with extrusion coating mold, linear plunger feeding, minimum material loss of about 18ml, maximum coating size of 200x300mm, can be used in a glove box, suitable for low viscosity less than 1000mPa. s, coating thickness accuracy of ± 1 μ m, can be optionally coated with scraper, wire rod, and four sid1

Tags :

LLZNO-500NM Lithium Lanthanum Zirconium Niobium Oxide Lithium ion Solid Electrolyte Powder

LLZNO-500NM Lithium Lanthanum Zirconium Niobium Oxide Lithium ion Solid Electrolyte Powder.

Tags :

15T Manual Hydraulic Press Machine For Lab Research

The 15t hydraulic press is equipped with molds of various sizes based on the mechanical lever principle. It is both practical and convenient.

Tags :

Manual powder tablet press(5T-40T Optional)

AOT-MC-540(5T-40T Optional) It is easy to operate and can be used without complex training, and users can flexibly adjust the pressure according to actual needs to adapt to the characteristics and pressing requirements of different powder materials

Tags :

Manual Hydraulic Press
Manual powder tablet press

Manganese Dioxide Positive Electrode Sheet

Manganese Dioxide Coated Stainless Steel Foil Positive Electrode Sheet of Zinc ion Battery

Water based zinc ion battery positive electrode sheet, coated with active material (manganese based or vanadium based) On the surface of the current collector, pole pieces are made by rolling, die-cutting, etc., with high loading capacity, controllability, good processability, and adjustable pole piece parameter size.

Tags :

Laboratory Pouch Cell Making Case Forming Machine for Aluminum Laminated Film

This compact pouch case forming machine is suitable forpouch cell case forming of aluminumlaminated film of flexible packaging lithium battery, driven by pneumatic.

Tags :

AOT-AFA-EI300 Scraper Three Roll Transfer Battery Coating Machine

AOT-AFA-EI300 scraper three roll transfer coating machine, roll to roll method, continuous and intermittent coating, width 300mm, coating width 50-260mm, coating surface density accuracy ± 1.5%, 150 ℃ hot air oven, suitable for 8-30 μ m thick metal substrates, including slurry stirring, winding correction function, optional NMP treatment and plasma1

Tags :