Lab CR2032 Casing Suppliers,Lab CR2032 Casing Manufacturers

NMC622 Single Side Coated Aluminum Foil for Battery Cathode Electrode Sheet

Reference for the use of Electrode Sheet: ①Electrode sheet cutting: AOT-DC-80 Cutting machine Recommended size of button electrode sheet: 12mm/14mm diameter. ②Pole piece weighing: AOT series balance active substance formula: active substance mass = (pole piece mass (mg) - disc area (cm2) * collector surface density (mg/cm2) * active substance propo1

Tags :

Lithium Battery Material LiBOB Poweder For Lab Research

In lithium-ion batteries, the main role of LiBOB is to transport particles and conduct current. To perform these tasks effectively, it requires high solubility and conductivity, good chemical stability, and a wide electrochemical window. The anionic structure of LiBOB molecule has delocalization, which makes it exhibit excellent performance in the 1

Tags :

Lithium Battery Cathode Material lithium difluorophosphate Poweder For Lab Research

Lithium difluorophosphate is an inorganic compound with the chemical formula LiPO₂F₂. This substance mainly appears as a white powdery solid, with a melting point higher than 300°C, a density of 1.979g/cm³, and a solubility of 40324mg/L at 20°C. Its vapour pressure is 0.000000145Pa at 25°C and 298K. Lithium difluorophosphate has a wide range of app1

Tags :

High pure Battery Material LiTFSI Poweder For Lab Research

Lithium bistrifluoromethylsulfonimide is a white crystal or powder that has good thermal stability and begins to decompose when heated to 360 ° C. It has high electrochemical stability and conductivity, and has corrosion effect on aluminum collector at high voltage (above 4.2V). Therefore, it is often used as a lithium ion battery, organic electrol1

Tags :

Heat Roller Press Machine For Battery Electrode Sheet Calendering With Winding System

1.This Roll Press Machine is a continuous roll to roll heat calendering machine . It has dual rollers of 150mm dia. x 300mm width and dual micrometer. The roll press machine is an ideal hot rolling press for adjusting thickness and increasing active material density of the electrode in Li-Ion batteries research after coating and drying. 21

Tags :

Battery Material high purity Potassium Metal Chips

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Al-Clad CR2032 Coin Cell Case (20d x 3.2mm) for Li-ion Battery

This is a special CR2032 coin cell case with Aluminum coated on the inside and outside of the positive can (60pcs/pack). It can tolerate polarization of higher voltages (up to 5.5V) due to the passivation of cladding by electrolyte component (especially LiPF6 based electrolyte system) to form a layer of AlF3. This AlF3 layer is 1

Tags :

Double Dispersed Axis Vacuum Planetary Mixer For Lithium Battery

MSK-SFM-9-5L dual dispersing shaft vacuum planetary mixer is an efficient mixing device that integrates low-speed mixing and high-speed dispersion. It combines orbital and rotational motion to achieve thorough mixing of materials.

Tags :

Lab Flatbed Coating Machine

MSK-AFA-PD200 flatbed coating machine, equipped with extrusion coating mold, linear plunger feeding, minimum material loss of about 18ml, maximum coating size of 200x300mm, can be used in a glove box, suitable for low viscosity less than 1000mPa. s, coating thickness accuracy of ± 1 μ m, can be optionally coated with scraper, wire rod, and four sid1

Tags :

AOT-AFA-EI300 Scraper Three Roll Transfer Battery Coating Machine

AOT-AFA-EI300 scraper three roll transfer coating machine, roll to roll method, continuous and intermittent coating, width 300mm, coating width 50-260mm, coating surface density accuracy ± 1.5%, 150 ℃ hot air oven, suitable for 8-30 μ m thick metal substrates, including slurry stirring, winding correction function, optional NMP treatment and plasma1

Tags :

Narrow Slit Extrusion Laboratory Coating Machine

AOT-AFA-SD300 narrow slit extrusion coating machine, roll to roll method, continuous and intermittent coating, width 300mm, coating width 50-260mm, optional extrusion coating die head, coating surface density accuracy ± 1.5%, 150 ℃ hot air oven, suitable for 8-30 μ m thick metal substrates, optional NMP treatment and feeding device.

Tags :