Lab Coin Cell Electrode Sheet Cutter Suppliers,Lab Coin Cell Electrode Sheet Cutter Manufacturers

Lithium sulfur battery carbon sulfur composite positive double-sided electrode plate

Lithium-sulfur battery is the next generation of high energy density electrochemical energy storage device, the carbon and sulfur composite positive electrode double-sided electrode plate is the key component to improve its performance. This electrode sheet uses advanced carbon-sulfur composite technology to effectively compound highly conductive c1

Tags :

Compact Electric Ring Disc Cutter For Lithium Battery Machine

AOT-MSK-T13 electric ring disc cutter is a pressure controlled battery cutter. This press is driven by a motor, which solves the problem of oil leakage in the glove box of traditional hydraulic presses. It is also small in size, making it easy to pass through the transition compartment inside the glove box. It also can cut round disc and rectangula1

Tags :

Battery Anode Material Potassium Metal Chips For Lab Reseaarch

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Battery Material high purity Potassium Metal Chips

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

potassium metal chips for coin cell

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Battery Automatic Assembly Machine Stacking Machine for Pouch Cell Battery

1、Equipment Overview This equipment is mainly used for experimental square lithium-ion power battery cell Z-shaped stacking, the equipment adopts automatic tension control system, cylinder driven diaphragm reciprocating movement, manual pressure knife to assist stacking, with high stacking efficiency, neatness and good characteristics. 2、Work flow 1

Tags :

AOT-MSK-CSC-B350 the Micro-Battery Electrodes Slitting Machine

This equipment is used for the slitting process of lithium battery electrode coil, mainly suitable for cutting multiple narrow strips. The equipment has high cutting accuracy, adopts closed-loop tension control, and has a stable cutting structure. After cutting, the pole pieces have no defects such as ruffles, burrs, indentations, etc. Designed for1

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Al-Clad CR2032 Coin Cell Case (20d x 3.2mm) for Li-ion Battery

This is a special CR2032 coin cell case with Aluminum coated on the inside and outside of the positive can (60pcs/pack). It can tolerate polarization of higher voltages (up to 5.5V) due to the passivation of cladding by electrolyte component (especially LiPF6 based electrolyte system) to form a layer of AlF3. This AlF3 layer is 1

Tags :

Double Dispersed Axis Vacuum Planetary Mixer For Lithium Battery

MSK-SFM-9-5L dual dispersing shaft vacuum planetary mixer is an efficient mixing device that integrates low-speed mixing and high-speed dispersion. It combines orbital and rotational motion to achieve thorough mixing of materials.

Tags :

In-situ Analytical Split Test Cell for Lithium/Zinc Air Battery

It contains a quartz observation window on the bottom which allows in-situ X-Ray analysis of battery material phase transition during charging and discharging process. Two needle valves allow you control air flow pressure and its splittable design provides you the most convenient way to test various anode and cathode materials. It's1

Tags :

Lab Flatbed Coating Machine

MSK-AFA-PD200 flatbed coating machine, equipped with extrusion coating mold, linear plunger feeding, minimum material loss of about 18ml, maximum coating size of 200x300mm, can be used in a glove box, suitable for low viscosity less than 1000mPa. s, coating thickness accuracy of ± 1 μ m, can be optionally coated with scraper, wire rod, and four sid1

Tags :