Al Plastic Film Forming Machine

Lithium Battery Aluminium Foil Coating Machine with Vacuum Pump and Dryer

description： The battery coating machine is a device specially used for uniformly coating the surface of the positive and negative electrode materials of the battery. It enables precise control of coating thickness and speed to ensure the stability of coating quality and performance. In the lithium battery production process, the battery coating ma1

Tags :

Battery Automatic Assembly Machine Stacking Machine for Pouch Cell Battery

1、Equipment Overview This equipment is mainly used for experimental square lithium-ion power battery cell Z-shaped stacking, the equipment adopts automatic tension control system, cylinder driven diaphragm reciprocating movement, manual pressure knife to assist stacking, with high stacking efficiency, neatness and good characteristics. 2、Work flow 1

Tags :

LiCl Anhydrous Lithium Chloride Powder for Solid State Electrolyte

Lithium Chloride (LiCl) Powder is a kind of battery-grade precursor to systhesize Li-based solid-state electrolyte. It has advantages such as high specific capacity and high voltage difference, which effectively enhance the power performance of the battery.

Tags :

AOT-MSK-CSC-B350 the Micro-Battery Electrodes Slitting Machine

This equipment is used for the slitting process of lithium battery electrode coil, mainly suitable for cutting multiple narrow strips. The equipment has high cutting accuracy, adopts closed-loop tension control, and has a stable cutting structure. After cutting, the pole pieces have no defects such as ruffles, burrs, indentations, etc. Designed for1

Tags :

Desk-Top Dual-Shaft Planetary Vacuum Mixer w/ Optional Containers

AOT-SFM-16 is a compact dual-shaft planetary vacuum mixer. Compared to single-shaft models, the dual-shaft mixer comes with three segments of programmable mixing speed from 0 - 600 rpm, which provides more uniform slurry mixing. It has a built-in pump for removing the gas bubble, which can vacuum the mixing container to -0.08 MPa. One 150ml S1

Tags :

Lithium battery coaxial double cylinder structure SSR viscometer (special for small samples) is suitable for 7ml-13ml

A new LV-SSR Brinell rotary viscometer adopts high performance stepping motor and driver, which runs accurately and smoothly according to the program setting, and the motor runs through the torque sensor to drive the rotor to rotate at constant speed. When the rotor is subjected to viscous resistance in the measured liquid, the force is fed back to1

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Al-Clad CR2032 Coin Cell Case (20d x 3.2mm) for Li-ion Battery

This is a special CR2032 coin cell case with Aluminum coated on the inside and outside of the positive can (60pcs/pack). It can tolerate polarization of higher voltages (up to 5.5V) due to the passivation of cladding by electrolyte component (especially LiPF6 based electrolyte system) to form a layer of AlF3. This AlF3 layer is 1

Tags :

Double Dispersed Axis Vacuum Planetary Mixer For Lithium Battery

MSK-SFM-9-5L dual dispersing shaft vacuum planetary mixer is an efficient mixing device that integrates low-speed mixing and high-speed dispersion. It combines orbital and rotational motion to achieve thorough mixing of materials.

Tags :

Lab Flatbed Coating Machine

MSK-AFA-PD200 flatbed coating machine, equipped with extrusion coating mold, linear plunger feeding, minimum material loss of about 18ml, maximum coating size of 200x300mm, can be used in a glove box, suitable for low viscosity less than 1000mPa. s, coating thickness accuracy of ± 1 μ m, can be optionally coated with scraper, wire rod, and four sid1

Tags :