Lab Small Vacuum Mixer Suppliers,Lab Small Vacuum Mixer Manufacturers

Lithium Battery Cathode Material lithium difluorophosphate Poweder For Lab Research

Lithium difluorophosphate is an inorganic compound with the chemical formula LiPO₂F₂. This substance mainly appears as a white powdery solid, with a melting point higher than 300°C, a density of 1.979g/cm³, and a solubility of 40324mg/L at 20°C. Its vapour pressure is 0.000000145Pa at 25°C and 298K. Lithium difluorophosphate has a wide range of app1

Tags :

High pure Battery Material LiTFSI Poweder For Lab Research

Lithium bistrifluoromethylsulfonimide is a white crystal or powder that has good thermal stability and begins to decompose when heated to 360 ° C. It has high electrochemical stability and conductivity, and has corrosion effect on aluminum collector at high voltage (above 4.2V). Therefore, it is often used as a lithium ion battery, organic electrol1

Tags :

Lab Tube Furnace Single Phase Electric 1200C Vacuum Tubular Furnace with Small Quartz Tube

This tubular furnace takes resistance wire as heating element, adopts double shell structure and temperature control meter, can carry out 30 stage programmed temperature control, phase shift trigger, thyristor control, furnace adopts alumina polycrystalline fiber material, both ends of the furnace tube can be sealed by stainless steel flange, stain1

Tags :

Tube Furnace Single Phase Electric Vacuum Tube Furnace with Small Quartz Tube

Tubular furnace is a commonly used heating equipment, mainly composed of furnace body, heating element, temperature control system and other parts.

Tags :

Heat Roller Press Machine For Battery Electrode Sheet Calendering With Winding System

1.This Roll Press Machine is a continuous roll to roll heat calendering machine . It has dual rollers of 150mm dia. x 300mm width and dual micrometer. The roll press machine is an ideal hot rolling press for adjusting thickness and increasing active material density of the electrode in Li-Ion batteries research after coating and drying. 21

Tags :

Battery Material high purity Potassium Metal Chips

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Lab Battery Slurry Vacuum Film Coating Machine with Dryer

Vacuum film coating machine is widely used in various high temperature coating process, such as ceramic film, crystal film, battery electrode, special nano film

Tags :

Desk-Top Dual-Shaft Planetary Vacuum Mixer w/ Optional Containers

AOT-SFM-16 is a compact dual-shaft planetary vacuum mixer. Compared to single-shaft models, the dual-shaft mixer comes with three segments of programmable mixing speed from 0 - 600 rpm, which provides more uniform slurry mixing. It has a built-in pump for removing the gas bubble, which can vacuum the mixing container to -0.08 MPa. One 150ml S1

Tags :

Lithium battery coaxial double cylinder structure SSR viscometer (special for small samples) is suitable for 7ml-13ml

A new LV-SSR Brinell rotary viscometer adopts high performance stepping motor and driver, which runs accurately and smoothly according to the program setting, and the motor runs through the torque sensor to drive the rotor to rotate at constant speed. When the rotor is subjected to viscous resistance in the measured liquid, the force is fed back to1

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Double Dispersed Axis Vacuum Planetary Mixer For Lithium Battery

MSK-SFM-9-5L dual dispersing shaft vacuum planetary mixer is an efficient mixing device that integrates low-speed mixing and high-speed dispersion. It combines orbital and rotational motion to achieve thorough mixing of materials.

Tags :

Lab Flatbed Coating Machine

MSK-AFA-PD200 flatbed coating machine, equipped with extrusion coating mold, linear plunger feeding, minimum material loss of about 18ml, maximum coating size of 200x300mm, can be used in a glove box, suitable for low viscosity less than 1000mPa. s, coating thickness accuracy of ± 1 μ m, can be optionally coated with scraper, wire rod, and four sid1

Tags :