Lab Sealer For Pouch Cell Suppliers,Lab Sealer For Pouch Cell Manufacturers

Heat Roller Press Machine For Battery Electrode Sheet Calendering With Winding System

1.This Roll Press Machine is a continuous roll to roll heat calendering machine . It has dual rollers of 150mm dia. x 300mm width and dual micrometer. The roll press machine is an ideal hot rolling press for adjusting thickness and increasing active material density of the electrode in Li-Ion batteries research after coating and drying. 21

Tags :

Battery Anode Material Potassium Metal Chips For Lab Reseaarch

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Battery Material high purity Potassium Metal Chips

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

potassium metal chips for coin cell

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Lab Battery Slurry Vacuum Film Coating Machine with Dryer

Vacuum film coating machine is widely used in various high temperature coating process, such as ceramic film, crystal film, battery electrode, special nano film

Tags :

Battery Automatic Assembly Machine Stacking Machine for Pouch Cell Battery

1、Equipment Overview This equipment is mainly used for experimental square lithium-ion power battery cell Z-shaped stacking, the equipment adopts automatic tension control system, cylinder driven diaphragm reciprocating movement, manual pressure knife to assist stacking, with high stacking efficiency, neatness and good characteristics. 2、Work flow 1

Tags :

Lithium battery coaxial double cylinder structure SSR viscometer (special for small samples) is suitable for 7ml-13ml

A new LV-SSR Brinell rotary viscometer adopts high performance stepping motor and driver, which runs accurately and smoothly according to the program setting, and the motor runs through the torque sensor to drive the rotor to rotate at constant speed. When the rotor is subjected to viscous resistance in the measured liquid, the force is fed back to1

Tags :

pouch pack battery test clamp Lithium ion pressure cycle test fixture

The pocket battery test clip ensures that the battery remains stable when subjected to pressure or external forces, thus accurately measuring the battery's performance parameters such as voltage, current, internal resistance, etc. The design of this fixture usually takes into account the size, shape and material of the battery to ensure the accurac1

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Al-Clad CR2032 Coin Cell Case (20d x 3.2mm) for Li-ion Battery

This is a special CR2032 coin cell case with Aluminum coated on the inside and outside of the positive can (60pcs/pack). It can tolerate polarization of higher voltages (up to 5.5V) due to the passivation of cladding by electrolyte component (especially LiPF6 based electrolyte system) to form a layer of AlF3. This AlF3 layer is 1

Tags :

Double Dispersed Axis Vacuum Planetary Mixer For Lithium Battery

MSK-SFM-9-5L dual dispersing shaft vacuum planetary mixer is an efficient mixing device that integrates low-speed mixing and high-speed dispersion. It combines orbital and rotational motion to achieve thorough mixing of materials.

Tags :

In-situ Analytical Split Test Cell for Lithium/Zinc Air Battery

It contains a quartz observation window on the bottom which allows in-situ X-Ray analysis of battery material phase transition during charging and discharging process. Two needle valves allow you control air flow pressure and its splittable design provides you the most convenient way to test various anode and cathode materials. It's1

Tags :