Conical Spring For Coin Cell Assembly Suppliers,Conical Spring For Coin Cell Assembly Manufacturers

Lithium Battery Cathode Material lithium difluorophosphate Poweder For Lab Research

Lithium difluorophosphate is an inorganic compound with the chemical formula LiPO₂F₂. This substance mainly appears as a white powdery solid, with a melting point higher than 300°C, a density of 1.979g/cm³, and a solubility of 40324mg/L at 20°C. Its vapour pressure is 0.000000145Pa at 25°C and 298K. Lithium difluorophosphate has a wide range of app1

Tags :

High pure Battery Material LiTFSI Poweder For Lab Research

Lithium bistrifluoromethylsulfonimide is a white crystal or powder that has good thermal stability and begins to decompose when heated to 360 ° C. It has high electrochemical stability and conductivity, and has corrosion effect on aluminum collector at high voltage (above 4.2V). Therefore, it is often used as a lithium ion battery, organic electrol1

Tags :

Battery Anode Material Potassium Metal Chips For Lab Reseaarch

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

potassium metal chips for coin cell

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Lab Battery Slurry Vacuum Film Coating Machine with Dryer

Vacuum film coating machine is widely used in various high temperature coating process, such as ceramic film, crystal film, battery electrode, special nano film

Tags :

Battery Automatic Assembly Machine Stacking Machine for Pouch Cell Battery

1、Equipment Overview This equipment is mainly used for experimental square lithium-ion power battery cell Z-shaped stacking, the equipment adopts automatic tension control system, cylinder driven diaphragm reciprocating movement, manual pressure knife to assist stacking, with high stacking efficiency, neatness and good characteristics. 2、Work flow 1

Tags :

Lithium battery coaxial double cylinder structure SSR viscometer (special for small samples) is suitable for 7ml-13ml

A new LV-SSR Brinell rotary viscometer adopts high performance stepping motor and driver, which runs accurately and smoothly according to the program setting, and the motor runs through the torque sensor to drive the rotor to rotate at constant speed. When the rotor is subjected to viscous resistance in the measured liquid, the force is fed back to1

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Al-Clad CR2032 Coin Cell Case (20d x 3.2mm) for Li-ion Battery

This is a special CR2032 coin cell case with Aluminum coated on the inside and outside of the positive can (60pcs/pack). It can tolerate polarization of higher voltages (up to 5.5V) due to the passivation of cladding by electrolyte component (especially LiPF6 based electrolyte system) to form a layer of AlF3. This AlF3 layer is 1

Tags :

In-situ Analytical Split Test Cell for Lithium/Zinc Air Battery

It contains a quartz observation window on the bottom which allows in-situ X-Ray analysis of battery material phase transition during charging and discharging process. Two needle valves allow you control air flow pressure and its splittable design provides you the most convenient way to test various anode and cathode materials. It's1

Tags :

Lab Flatbed Coating Machine

MSK-AFA-PD200 flatbed coating machine, equipped with extrusion coating mold, linear plunger feeding, minimum material loss of about 18ml, maximum coating size of 200x300mm, can be used in a glove box, suitable for low viscosity less than 1000mPa. s, coating thickness accuracy of ± 1 μ m, can be optionally coated with scraper, wire rod, and four sid1

Tags :

precision semi-automatic die cutter for pouch cell electrode sheets

AOT-MSK-180-N is a precision semi-automatic die cutter for pouch cell electrode sheets (Max. 200mm L x 200mm W). It is an updated version of MSK-180 with more stability and better accuracy at reducing the burrs and powder-shedding of the electrode sheets.

Tags :