Coin Cell Lab Line Equipment Suppliers,Coin Cell Lab Line Equipment Manufacturers

Lithium Battery Cathode Material lithium difluorophosphate Poweder For Lab Research

Lithium difluorophosphate is an inorganic compound with the chemical formula LiPO₂F₂. This substance mainly appears as a white powdery solid, with a melting point higher than 300°C, a density of 1.979g/cm³, and a solubility of 40324mg/L at 20°C. Its vapour pressure is 0.000000145Pa at 25°C and 298K. Lithium difluorophosphate has a wide range of app1

Tags :

High pure Battery Material LiTFSI Poweder For Lab Research

Lithium bistrifluoromethylsulfonimide is a white crystal or powder that has good thermal stability and begins to decompose when heated to 360 ° C. It has high electrochemical stability and conductivity, and has corrosion effect on aluminum collector at high voltage (above 4.2V). Therefore, it is often used as a lithium ion battery, organic electrol1

Tags :

Heat Roller Press Machine For Battery Electrode Sheet Calendering With Winding System

1.This Roll Press Machine is a continuous roll to roll heat calendering machine . It has dual rollers of 150mm dia. x 300mm width and dual micrometer. The roll press machine is an ideal hot rolling press for adjusting thickness and increasing active material density of the electrode in Li-Ion batteries research after coating and drying. 21

Tags :

Battery Anode Material Potassium Metal Chips For Lab Reseaarch

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Battery Material high purity Potassium Metal Chips

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

potassium metal chips for coin cell

99.7% High Purity Electrode Potassium Metal Chips For CR2032 2025 2016 Coin Cell Case.

Tags :

Lithium Battery Aluminium Foil Coating Machine with Vacuum Pump and Dryer

description： The battery coating machine is a device specially used for uniformly coating the surface of the positive and negative electrode materials of the battery. It enables precise control of coating thickness and speed to ensure the stability of coating quality and performance. In the lithium battery production process, the battery coating ma1

Tags :

Battery Automatic Assembly Machine Stacking Machine for Pouch Cell Battery

1、Equipment Overview This equipment is mainly used for experimental square lithium-ion power battery cell Z-shaped stacking, the equipment adopts automatic tension control system, cylinder driven diaphragm reciprocating movement, manual pressure knife to assist stacking, with high stacking efficiency, neatness and good characteristics. 2、Work flow 1

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Al-Clad CR2032 Coin Cell Case (20d x 3.2mm) for Li-ion Battery

This is a special CR2032 coin cell case with Aluminum coated on the inside and outside of the positive can (60pcs/pack). It can tolerate polarization of higher voltages (up to 5.5V) due to the passivation of cladding by electrolyte component (especially LiPF6 based electrolyte system) to form a layer of AlF3. This AlF3 layer is 1

Tags :

Double Dispersed Axis Vacuum Planetary Mixer For Lithium Battery

MSK-SFM-9-5L dual dispersing shaft vacuum planetary mixer is an efficient mixing device that integrates low-speed mixing and high-speed dispersion. It combines orbital and rotational motion to achieve thorough mixing of materials.

Tags :

In-situ Analytical Split Test Cell for Lithium/Zinc Air Battery

It contains a quartz observation window on the bottom which allows in-situ X-Ray analysis of battery material phase transition during charging and discharging process. Two needle valves allow you control air flow pressure and its splittable design provides you the most convenient way to test various anode and cathode materials. It's1

Tags :