Al Clad Cr2032 Coin Cell Case

Lithium Battery Aluminium Foil Coating Machine with Vacuum Pump and Dryer

description： The battery coating machine is a device specially used for uniformly coating the surface of the positive and negative electrode materials of the battery. It enables precise control of coating thickness and speed to ensure the stability of coating quality and performance. In the lithium battery production process, the battery coating ma1

Tags :

Battery Automatic Assembly Machine Stacking Machine for Pouch Cell Battery

1、Equipment Overview This equipment is mainly used for experimental square lithium-ion power battery cell Z-shaped stacking, the equipment adopts automatic tension control system, cylinder driven diaphragm reciprocating movement, manual pressure knife to assist stacking, with high stacking efficiency, neatness and good characteristics. 2、Work flow 1

Tags :

LiCl Anhydrous Lithium Chloride Powder for Solid State Electrolyte

Lithium Chloride (LiCl) Powder is a kind of battery-grade precursor to systhesize Li-based solid-state electrolyte. It has advantages such as high specific capacity and high voltage difference, which effectively enhance the power performance of the battery.

Tags :

Lithium battery coaxial double cylinder structure SSR viscometer (special for small samples) is suitable for 7ml-13ml

A new LV-SSR Brinell rotary viscometer adopts high performance stepping motor and driver, which runs accurately and smoothly according to the program setting, and the motor runs through the torque sensor to drive the rotor to rotate at constant speed. When the rotor is subjected to viscous resistance in the measured liquid, the force is fed back to1

Tags :

Battery cathode material Na3V2(PO4)202F

Na3V2(PO4)202F material has good structural stability and can maintain a high capacity retention rate after multiple charge and discharge cycles, which can extend the service life of the battery and reduce the use cost. Sodium vanadium fluorooxyphosphate has a high theoretical specific capacity, the theoretical specific capacity can reach 130mAh/g 1

Tags :

Al-Clad CR2032 Coin Cell Case (20d x 3.2mm) for Li-ion Battery

This is a special CR2032 coin cell case with Aluminum coated on the inside and outside of the positive can (60pcs/pack). It can tolerate polarization of higher voltages (up to 5.5V) due to the passivation of cladding by electrolyte component (especially LiPF6 based electrolyte system) to form a layer of AlF3. This AlF3 layer is 1

Tags :

In-situ Analytical Split Test Cell for Lithium/Zinc Air Battery

It contains a quartz observation window on the bottom which allows in-situ X-Ray analysis of battery material phase transition during charging and discharging process. Two needle valves allow you control air flow pressure and its splittable design provides you the most convenient way to test various anode and cathode materials. It's1

Tags :

LLZNO-500NM Lithium Lanthanum Zirconium Niobium Oxide Lithium ion Solid Electrolyte Powder

LLZNO-500NM Lithium Lanthanum Zirconium Niobium Oxide Lithium ion Solid Electrolyte Powder.

Tags :

15T Manual Hydraulic Press Machine For Lab Research

The 15t hydraulic press is equipped with molds of various sizes based on the mechanical lever principle. It is both practical and convenient.

Tags :

Manual powder tablet press(5T-40T Optional)

AOT-MC-540(5T-40T Optional) It is easy to operate and can be used without complex training, and users can flexibly adjust the pressure according to actual needs to adapt to the characteristics and pressing requirements of different powder materials

Tags :

Manual Hydraulic Press
Manual powder tablet press

Manganese Dioxide Positive Electrode Sheet

Manganese Dioxide Coated Stainless Steel Foil Positive Electrode Sheet of Zinc ion Battery

Water based zinc ion battery positive electrode sheet, coated with active material (manganese based or vanadium based) On the surface of the current collector, pole pieces are made by rolling, die-cutting, etc., with high loading capacity, controllability, good processability, and adjustable pole piece parameter size.

Tags :

precision semi-automatic die cutter for pouch cell electrode sheets

AOT-MSK-180-N is a precision semi-automatic die cutter for pouch cell electrode sheets (Max. 200mm L x 200mm W). It is an updated version of MSK-180 with more stability and better accuracy at reducing the burrs and powder-shedding of the electrode sheets.

Tags :